Motors
For use with FlowGo Control Interface.


Sort | Name:    Order No.:    Default View | List  Grid

Light sensor (unhoused)
This ready to use Light level sensor is a Light Dependent Resistor wired to a 3.5 mm jack plug. It is an analogue sensor that connects to a Sensor Input on FlowGo.  
Order No. 6253
More Info
Light Sensor (Housed)
This ready to use Light level sensor is a Light Dependent Resistor housed in a durable plastic case and wired to a 3.5 mm jack plug. It is an analogue sensor that connects to a Sensor Input on FlowGo....
Order No. 6256
More Info
Temperature Sensor (unhoused)
This ready to use Temperature sensor has an exposed thermistor wired to a 3.5 mm jack plug. It is an analogue sensor that connects to a Sensor Input on FlowGo.  
Order No. 6252
More Info
Temperature Sensor (Housed)
This ready to use Temperature sensor has a thermistor housed in a protective tube, wired to a 3.5 mm jack plug. It is an analogue sensor that connects to a Sensor Input on FlowGo.  
Order No. 6255
More Info
Control Switches Set
A set of 4 Input devices (switches), all with 2 metres of wire and colour coded 4 mm plugs, ready to use with FlowGo.
Order No. 3666
More Info
Light Switch
Useful for lighthouse models or a light beam alarm (set to go off when something passes between the LDR and a light beam).  
Order No. 3661
More Info
Proximity Switch
The Proximity Switch (otherwise known as a reed switch) is supplied with a separate magnet. 
Order No. 3664
More Info
Push Switch
This is a momentary push-to-make switch.
Order No. 3654
More Info
Small Pressure Pad Switch
Use for model roads and entrances. It is only 6 cm long, and is sensitive enough to be triggered by hand pressure, or a toy car pushed over it.  
Order No. 3663
More Info
Tilt Switch
This switch could be used as a limit switch for moving models e.g. bridges, fairground rides and barriers.  
Order No. 3662
More Info
C Battery Holder (Takes 4 x 1.5V Batteries)
4 x 1.5V C Battery Holders  
Order No. 3655
More Info
6 V Light Bulb and Holder
A 6 V light bulb and holder attached to 2 metres of cable with colour coded 4 mm plugs, ready to connect as an Output to FlowGo or Learn & Go.
Order No. 3651
More Info
6 V Round Piezo Buzzer
A 6 V round Piezo buzzer attached to 2 metres of cable with colour coded 4 mm plugs, ready to connect as an Output to FlowGo or Learn & Go.  
Order No. 3652
More Info
6V Square Buzzer
A 6 V square buzzer attached to 2 metres of cable with colour coded 4 mm plugs. Ready to connect as an Output to FlowGo or Learn & Go.
Order No. 3658
More Info
Control Output Set
A set of 5 Output devices, all with 2 metres of wire and colour coded 4 mm plugs, ready to use with FlowGo and Learn & Go.
Order No. 3665
More Info
Easy LEDs
A set of 6 coloured LEDs (2 red, 2 amber and 2 green) attached to 1 metre of ribbon cable with colour coded 4 mm plugs, ready to connect as an Output to FlowGo or Learn & Go.
Order No. 3616
More Info
Clearbox Motor with Gears
A 3 to 6 V Clearbox motor with a pre-assembled low speed, high torque adjustable plastic gearbox with a 4 mm diameter drive shaft.
Order No. 3653
More Info
Economy Motor with Gearbox
A 3 to 6 V motor with pre-assembled medium speed, medium torque plastic gearbox with a 4 mm diameter drive shaft.
Order No. 3671
More Info
Economy Motor with Pulley
A 3 to 6 V high speed, high torque motor with motor pulley. For use with a drive belt, rubber band or pulley system to power small models.
Order No. 3659
More Info
Mains Power Supply (6V)
6V Power Supply
Order No. 3611/2
More Info
PP3 Battery Connection
Battery clip connector.
Order No. 6339
More Info
Mounting Clips (Pack of 10)
Pack of 10 plastic spring clips and sticky pads.
Order No. 3669
More Info
Spring Connectors (Pack of 10)
This pack of 10 connectors provide an easy connection system for bare wires to control interfaces that have 4 mm sockets.  
Order No. CK6
More Info
Sort | Name:    Order No.:    Default View | List  Grid

We are BESA Members - Learn about the code of practice

The BESA Code of Practice is a mandatory membership commitment given by members to BESA. Each member is expected, as a condition of Membership, to meet the ethical standards provided for in this Code of Practice in that Member’s relationship with the Member’s customers. More Info...